MWMoldedPartValidationBuilder Class¶

class NXOpen.Tooling.MWMoldedPartValidationBuilder¶

Bases: NXOpen.Builder

Represents a builder to be used to perform Molded Part Validation analysis.

To create a new instance of this class, use NXOpen.Tooling.MWMoldedPartValidationManager.CreateMWMoldedPartValidationBuilder()

Default values.

Property	Value
CalculationOption	KeepExisting
FaceDraftAngleLimit	3
FaceHighlightSelectedFaces	1
FaceNonSelectedFacesTranslucency	0
FaceSelectAllFaces	0
FaceSelectCrossoverFaces	0
FaceSelectNegativeFaces1	0
FaceSelectNegativeFaces2	0
FaceSelectPositiveFaces1	0
FaceSelectPositiveFaces2	0
FaceSelectUndercutAreas	0
FaceSelectUndercutEdges	0
FaceSelectVerticalFaces	0
FaceSelectedFacesTranslucency	0
InformationCheckScope	FaceProperties
InformationLowerLimit	0
InformationLowerLimitR01	5.5
InformationLowerLimitR02	5
InformationLowerLimitR03	4.5
InformationLowerLimitR04	4
InformationLowerLimitR05	3.5
InformationLowerLimitR06	3
InformationLowerLimitR07	2.5
InformationLowerLimitR08	2
InformationLowerLimitR09	1.5
InformationLowerLimitR10	1
InformationLowerLimitR11	0.5
InformationLowerLimitR12	0
InformationRangeType	Uniform
InformationSharpAngleLimit	6
InformationShowBoundaryEdges	0
InformationShowRangeR01	0
InformationShowRangeR02	0
InformationShowRangeR03	0
InformationShowRangeR04	0
InformationShowRangeR05	0
InformationShowRangeR06	0
InformationShowRangeR07	0
InformationShowRangeR08	0
InformationShowRangeR09	0
InformationShowRangeR10	0
InformationShowRangeR11	0
InformationShowRangeR12	0
InformationShowSharpEdges	0
InformationUpperLimit	6
InformationUpperLimitR01	6
InformationUpperLimitR02	5.5
InformationUpperLimitR03	5
InformationUpperLimitR04	4.5
InformationUpperLimitR05	4
InformationUpperLimitR06	3.5
InformationUpperLimitR07	3
InformationUpperLimitR08	2.5
InformationUpperLimitR09	2
InformationUpperLimitR10	0.5
InformationUpperLimitR11	1
InformationUpperLimitR12	0.5
InformationUseSingleTolerance	0
RegionAssignToRegionOption	CavityRegion
RegionCavityRegionTranslucency	0
RegionCoreRegionTranslucency	0
RegionSelectCrossoverRegionFaces	0
RegionSelectCrossoverVerticalFaces	0
RegionSelectUnknownFaces	0
RegionShowIncompleteLoops	1
RegionShowInternalLoops	1
RegionShowPartingEdges	1

New in version NX8.0.0.

Properties¶

Property	Description
ActiveTabPage	Returns or sets the active tab page.
CalculationDrawDirection	Returns or sets the draw direction on the Calculate Tab page.
CalculationOption	Returns or sets the calculation option on the Calculate Tab page.
CalculationProductBody	Returns the product body to be analyzed on the Calculate Tab page.
FaceAllFacesColor	Returns or sets the color for applying to all faces on the Face Tab page.
FaceCrossoverFacesColor	Returns or sets the color for applying to the crossover faces on the Face Tab page.
FaceDraftAngleLimit	Returns or sets the draft angle limit on the Face Tab page.
FaceHighlightSelectedFaces	Returns or sets the option for highlighting the selected faces on the Face Tab page.
FaceNegativeFacesColor1	Returns or sets the color for applying to the negative small radius faces on the Face Tab page.
FaceNegativeFacesColor2	Returns or sets the color for applying to the negative faces on the Face Tab page.
FaceNonSelectedFacesTranslucency	Returns or sets the translucency for the non-selected faces on the Face Tab page.
FacePositiveFacesColor1	Returns or sets the color for applying to the positive faces on the Face Tab page.
FacePositiveFacesColor2	Returns or sets the color for applying to the positive small radius faces on the Face Tab page.
FaceSelectAllFaces	Returns or sets the option for turning on/off the selection of all faces on the Face Tab page.
FaceSelectCrossoverFaces	Returns or sets the option for turning on/off the highlight of the crossover faces on the Face Tab page.
FaceSelectNegativeFaces1	Returns or sets the option for turning on/off the highlight of the negative small radius faces on the Face Tab page.
FaceSelectNegativeFaces2	Returns or sets the option for turning on/off the highlight of the negative faces on the Face Tab page.
FaceSelectPositiveFaces1	Returns or sets the option for turning on/off the highlight of the positive faces on the Face Tab page.
FaceSelectPositiveFaces2	Returns or sets the option for turning on/off the highlight of the positive small radius faces on the Face Tab page.
FaceSelectUndercutAreas	Returns or sets the option for turning on/off the highlight of the undercut area faces on the Face Tab page.
FaceSelectUndercutEdges	Returns or sets the option for turning on/off the highlight of the undercut edges on the Face Tab page.
FaceSelectVerticalFaces	Returns or sets the option for turning on/off the highlight of the vertical faces on the Face Tab page.
FaceSelectedFacesTranslucency	Returns or sets the translucency for the selected faces on the Face Tab page.
FaceUndercutAreasColor	Returns or sets the color for applying to the undercut area faces on the Face Tab page.
FaceUndercutEdgesColor	Returns or sets the color for applying to the undercut edges on the Face Tab page.
FaceVerticalFacesColor	Returns or sets the color for applying to the vertical faces on the Face Tab page.
InApplyStatus	Returns or sets the flag that indicates the Apply status of the command, needed only in the interactive environment.
InformationCheckScope	Returns or sets the check scope on the Information Tab page.
InformationColorR01	Returns or sets the color of row 1 for the small radius faces on the Information Tab page.
InformationColorR02	Returns or sets the color of row 2 for the small radius faces on the Information Tab page.
InformationColorR03	Returns or sets the color of row 3 for the small radius faces on the Information Tab page.
InformationColorR04	Returns or sets the color of row 4 for the small radius faces on the Information Tab page.
InformationColorR05	Returns or sets the color of row 5 for the small radius faces on the Information Tab page.
InformationColorR06	Returns or sets the color of row 6 for the small radius faces on the Information Tab page.
InformationColorR07	Returns or sets the color of row 7 for the small radius faces on the Information Tab page.
InformationColorR08	Returns or sets the color of row 8 for the small radius faces on the Information Tab page.
InformationColorR09	Returns or sets the color of row 9 for the small radius faces on the Information Tab page.
InformationColorR10	Returns or sets the color of row 10 for the small radius faces on the Information Tab page.
InformationColorR11	Returns or sets the color of row 11 for the small radius faces on the Information Tab page.
InformationColorR12	Returns or sets the color of row 12 for the small radius faces on the Information Tab page.
InformationInspectFace	Returns the face selected face for displaying the face properties.
InformationLowerLimit	Returns or sets the lower limit of the range limit values on the Information Tab page.
InformationLowerLimitR01	Returns or sets the lower limit of row 1 for the small radius faces on the Information Tab page.
InformationLowerLimitR02	Returns or sets the lower limit of row 2 for the small radius faces on the Information Tab page.
InformationLowerLimitR03	Returns or sets the lower limit of row 3 for the small radius faces on the Information Tab page.
InformationLowerLimitR04	Returns or sets the lower limit of row 4 for the small radius faces on the Information Tab page.
InformationLowerLimitR05	Returns or sets the lower limit of row 5 for the small radius faces on the Information Tab page.
InformationLowerLimitR06	Returns or sets the lower limit of row 6 for the small radius faces on the Information Tab page.
InformationLowerLimitR07	Returns or sets the lower limit of row 7 for the small radius faces on the Information Tab page.
InformationLowerLimitR08	Returns or sets the lower limit of row 8 for the small radius faces on the Information Tab page.
InformationLowerLimitR09	Returns or sets the lower limit of row 9 for the small radius faces on the Information Tab page.
InformationLowerLimitR10	Returns or sets the lower limit of row 10 for the small radius faces on the Information Tab page.
InformationLowerLimitR11	Returns or sets the lower limit of row 11 for the small radius faces on the Information Tab page.
InformationLowerLimitR12	Returns or sets the lower limit of row 12 for the small radius faces on the Information Tab page.
InformationRangeType	Returns or sets the range type on the Information Tab page.
InformationSharpAngleLimit	Returns or sets the sharp angle limit on the Information Tab page.
InformationShowBoundaryEdges	Returns or sets the option for turning on/off the highlight of the boundary edges of the sheet body on the Information Tab page.
InformationShowRangeR01	Returns or sets the option of selecting the small radius faces within the range limit values of row 1 on the Information Tab page.
InformationShowRangeR02	Returns or sets the option of selecting the small radius faces within the range limit values of row 2 on the Information Tab page.
InformationShowRangeR03	Returns or sets the option of selecting the small radius faces within the range limit values of row 3 on the Information Tab page.
InformationShowRangeR04	Returns or sets the option of selecting the small radius faces within the range limit values of row 4 on the Information Tab page.
InformationShowRangeR05	Returns or sets the option of selecting the small radius faces within the range limit values of row 5 on the Information Tab page.
InformationShowRangeR06	Returns or sets the option of selecting the small radius faces within the range limit values of row 6 on the Information Tab page.
InformationShowRangeR07	Returns or sets the option of selecting the small radius faces within the range limit values of row 7 on the Information Tab page.
InformationShowRangeR08	Returns or sets the option of selecting the small radius faces within the range limit values of row 8 on the Information Tab page.
InformationShowRangeR09	Returns or sets the option of selecting the small radius faces within the range limit values of row 9 on the Information Tab page.
InformationShowRangeR10	Returns or sets the option of selecting the small radius faces within the range limit values of row 10 on the Information Tab page.
InformationShowRangeR11	Returns or sets the option of selecting the small radius faces within the range limit values of row 11 on the Information Tab page.
InformationShowRangeR12	Returns or sets the option of selecting the small radius faces within the range limit values of row 12 on the Information Tab page.
InformationShowSharpEdges	Returns or sets the option for turning on/off the highlight of the sharp edges of the sheet body on the Information Tab page.
InformationUpperLimit	Returns or sets the upper limit on the Information Tab page.
InformationUpperLimitR01	Returns or sets the upper limit of row 1 for the small radius faces on the Information Tab page.
InformationUpperLimitR02	Returns or sets the upper limit of row 2 for the small radius faces on the Information Tab page.
InformationUpperLimitR03	Returns or sets the upper limit of row 3 for the small radius faces on the Information Tab page.
InformationUpperLimitR04	Returns or sets the upper limit of row 4 for the small radius faces on the Information Tab page.
InformationUpperLimitR05	Returns or sets the upper limit of row 5 for the small radius faces on the Information Tab page.
InformationUpperLimitR06	Returns or sets the upper limit of row 6 for the small radius faces on the Information Tab page.
InformationUpperLimitR07	Returns or sets the upper limit of row 7 for the small radius faces on the Information Tab page.
InformationUpperLimitR08	Returns or sets the upper limit of row 8 for the small radius faces on the Information Tab page.
InformationUpperLimitR09	Returns or sets the upper limit of row 9 for the small radius faces on the Information Tab page.
InformationUpperLimitR10	Returns or sets the upper limit of row 10 for the small radius faces on the Information Tab page.
InformationUpperLimitR11	Returns or sets the upper limit of row 11 for the small radius faces on the Information Tab page.
InformationUpperLimitR12	Returns or sets the upper limit of row 12 for the small radius faces on the Information Tab page.
InformationUseSingleTolerance	Returns or sets the option for using a single tolerance for defining the range limit values on the Information Tab page.
RegionAssignToRegionOption	Returns or sets the option for assigning the selected region faces to the cavity or core region on the Region Tab page.
RegionCavityRegionColor	Returns or sets the color for applying to the cavity region faces on the Region Tab page.
RegionCavityRegionTranslucency	Returns or sets the translucency for applying to the cavity region faces on the Region Tab page.
RegionCoreRegionColor	Returns or sets the color for applying to the core region faces on the Region Tab page.
RegionCoreRegionTranslucency	Returns or sets the translucency for applying to the core region faces on the Region Tab page.
RegionFaces	Returns the faces selected for assigning to the cavity or core region.
RegionSelectCrossoverRegionFaces	Returns or sets the option for including or removing the crossover region faces in the selection on the Region Tab page.
RegionSelectCrossoverVerticalFaces	Returns or sets the option for including or removing the crossover vertical faces in the selection on the Region Tab page.
RegionSelectUnknownFaces	Returns or sets the option for including or removing the unknown faces in the selection on the Region Tab page.
RegionShowIncompleteLoops	Returns or sets the option for turning on/off the highlight of the incomplete loop edges.
RegionShowInternalLoops	Returns or sets the option for turning on/off the highlight of the internal loop edges.
RegionShowPartingEdges	Returns or sets the option for turning on/off the highlight of the parting edges.
RegionUndefinedRegionColor	Returns or sets the color for applying to the undefined region faces on the Region Tab page.
Tag	Returns the Tag for this object.

Methods¶

Method	Description
Calculate	Calculate button on the Calculate Tab page.
Commit	Commits any edits that have been applied to the builder.
Destroy	Deletes the builder, and cleans up any objects created by the builder.
FaceSetAllFacesColor	Action button for setting color on all faces on the Face Tab page.
GetCommittedObjects	For builders that create more than one object, this method returns the objects that are created by commit.
GetObject	Returns the object currently being edited by this builder.
InitMpvData	Initialize the MPV data for performing analysis in Molded Part Validation.
PerformModelPropertiesCalculation	Perform model properties calculation if the calculation has not been performed before.
PerformSharpCornersCalculation	Perform the sharp corners calculation if the calculation has not been performed before.
ProcessFaceSplit	Action button for invoking the Split Face command on the Face Tab page.
RegionSetRegionsColor	Action button for setting color on the cavity, core and undefined region faces on the Region Tab page.
SetCalculationProductBody	Set the product body to be analyzed on the Calculate Tab page.
ShowResults	Updates the model to reflect the result of an edit to the model for all builders that support showing results.
UpdateEjectDirection	Update the eject direction.
UpdateMpvData	Update the MPV data used in performing analysis in Molded Part Validation whenever there are changes in data on dialog.
UpdateSharpEdgesInformation	Update the sharp edges information based on the new sharp angle limit which has been changed by the user.
UpdateSmallRadiusFacesInformation	Update the small radius faces information based on the new range limits of the radius which has been changed by the user.
Validate	Validate whether the inputs to the component are sufficient for commit to be called.

Enumerations¶

MWMoldedPartValidationBuilderAssignToRegion Enumeration	Options for assigning faces to the Cavity or Core region
MWMoldedPartValidationBuilderCalculateOption Enumeration	Calculation options
MWMoldedPartValidationBuilderCheckScope Enumeration	Check scope for information
MWMoldedPartValidationBuilderRangeType Enumeration	Range type for displaying small corner radius faces

Property Detail¶

ActiveTabPage¶

MWMoldedPartValidationBuilder.ActiveTabPage¶

Returns or sets the active tab page.

-------------------------------------

Getter Method

Signature ActiveTabPage

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature ActiveTabPage

Parameters:	activeTabPage (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

CalculationDrawDirection¶

MWMoldedPartValidationBuilder.CalculationDrawDirection¶

Returns or sets the draw direction on the Calculate Tab page.

-------------------------------------

Getter Method

Signature CalculationDrawDirection

Returns:
Return type:	`NXOpen.Direction`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature CalculationDrawDirection

Parameters:	calculationDrawDirection (`NXOpen.Direction`) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

CalculationOption¶

MWMoldedPartValidationBuilder.CalculationOption¶

Returns or sets the calculation option on the Calculate Tab page.

-------------------------------------

Getter Method

Signature CalculationOption

Returns:
Return type:	`NXOpen.Tooling.MWMoldedPartValidationBuilderCalculateOption`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature CalculationOption

Parameters:	calculationOption (`NXOpen.Tooling.MWMoldedPartValidationBuilderCalculateOption`) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

CalculationProductBody¶

MWMoldedPartValidationBuilder.CalculationProductBody¶

Returns the product body to be analyzed on the Calculate Tab page.

-------------------------------------

Getter Method

Signature CalculationProductBody

Returns:
Return type:	`NXOpen.SelectBody`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceAllFacesColor¶

MWMoldedPartValidationBuilder.FaceAllFacesColor¶

Returns or sets the color for applying to all faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceAllFacesColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceAllFacesColor

Parameters:	faceAllFacesColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceCrossoverFacesColor¶

MWMoldedPartValidationBuilder.FaceCrossoverFacesColor¶

Returns or sets the color for applying to the crossover faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceCrossoverFacesColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceCrossoverFacesColor

Parameters:	faceCrossoverFacesColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceDraftAngleLimit¶

MWMoldedPartValidationBuilder.FaceDraftAngleLimit¶

Returns or sets the draft angle limit on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceDraftAngleLimit

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceDraftAngleLimit

Parameters:	faceDraftAngleLimit (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceHighlightSelectedFaces¶

MWMoldedPartValidationBuilder.FaceHighlightSelectedFaces¶

Returns or sets the option for highlighting the selected faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceHighlightSelectedFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceHighlightSelectedFaces

Parameters:	faceHighlightSelectedFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceNegativeFacesColor1¶

MWMoldedPartValidationBuilder.FaceNegativeFacesColor1¶

Returns or sets the color for applying to the negative small radius faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceNegativeFacesColor1

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceNegativeFacesColor1

Parameters:	faceNegativeFacesColor1 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceNegativeFacesColor2¶

MWMoldedPartValidationBuilder.FaceNegativeFacesColor2¶

Returns or sets the color for applying to the negative faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceNegativeFacesColor2

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceNegativeFacesColor2

Parameters:	faceNegativeFacesColor2 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceNonSelectedFacesTranslucency¶

MWMoldedPartValidationBuilder.FaceNonSelectedFacesTranslucency¶

Returns or sets the translucency for the non-selected faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceNonSelectedFacesTranslucency

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceNonSelectedFacesTranslucency

Parameters:	faceNonSelectedFacesTranslucency (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FacePositiveFacesColor1¶

MWMoldedPartValidationBuilder.FacePositiveFacesColor1¶

Returns or sets the color for applying to the positive faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FacePositiveFacesColor1

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FacePositiveFacesColor1

Parameters:	facePositiveFacesColor1 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FacePositiveFacesColor2¶

MWMoldedPartValidationBuilder.FacePositiveFacesColor2¶

Returns or sets the color for applying to the positive small radius faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FacePositiveFacesColor2

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FacePositiveFacesColor2

Parameters:	facePositiveFacesColor2 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectAllFaces¶

MWMoldedPartValidationBuilder.FaceSelectAllFaces¶

Returns or sets the option for turning on/off the selection of all faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectAllFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectAllFaces

Parameters:	faceSelectAllFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectCrossoverFaces¶

MWMoldedPartValidationBuilder.FaceSelectCrossoverFaces¶

Returns or sets the option for turning on/off the highlight of the crossover faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectCrossoverFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectCrossoverFaces

Parameters:	faceSelectCrossoverFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectNegativeFaces1¶

MWMoldedPartValidationBuilder.FaceSelectNegativeFaces1¶

Returns or sets the option for turning on/off the highlight of the negative small radius faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectNegativeFaces1

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectNegativeFaces1

Parameters:	faceSelectNegativeFaces1 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectNegativeFaces2¶

MWMoldedPartValidationBuilder.FaceSelectNegativeFaces2¶

Returns or sets the option for turning on/off the highlight of the negative faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectNegativeFaces2

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectNegativeFaces2

Parameters:	faceSelectNegativeFaces2 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectPositiveFaces1¶

MWMoldedPartValidationBuilder.FaceSelectPositiveFaces1¶

Returns or sets the option for turning on/off the highlight of the positive faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectPositiveFaces1

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectPositiveFaces1

Parameters:	faceSelectPositiveFaces1 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectPositiveFaces2¶

MWMoldedPartValidationBuilder.FaceSelectPositiveFaces2¶

Returns or sets the option for turning on/off the highlight of the positive small radius faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectPositiveFaces2

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectPositiveFaces2

Parameters:	faceSelectPositiveFaces2 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectUndercutAreas¶

MWMoldedPartValidationBuilder.FaceSelectUndercutAreas¶

Returns or sets the option for turning on/off the highlight of the undercut area faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectUndercutAreas

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectUndercutAreas

Parameters:	faceSelectUndercutAreas (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectUndercutEdges¶

MWMoldedPartValidationBuilder.FaceSelectUndercutEdges¶

Returns or sets the option for turning on/off the highlight of the undercut edges on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectUndercutEdges

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectUndercutEdges

Parameters:	faceSelectUndercutEdges (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectVerticalFaces¶

MWMoldedPartValidationBuilder.FaceSelectVerticalFaces¶

Returns or sets the option for turning on/off the highlight of the vertical faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectVerticalFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectVerticalFaces

Parameters:	faceSelectVerticalFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSelectedFacesTranslucency¶

MWMoldedPartValidationBuilder.FaceSelectedFacesTranslucency¶

Returns or sets the translucency for the selected faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceSelectedFacesTranslucency

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceSelectedFacesTranslucency

Parameters:	faceSelectedFacesTranslucency (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceUndercutAreasColor¶

MWMoldedPartValidationBuilder.FaceUndercutAreasColor¶

Returns or sets the color for applying to the undercut area faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceUndercutAreasColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceUndercutAreasColor

Parameters:	faceUndercutAreasColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceUndercutEdgesColor¶

MWMoldedPartValidationBuilder.FaceUndercutEdgesColor¶

Returns or sets the color for applying to the undercut edges on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceUndercutEdgesColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceUndercutEdgesColor

Parameters:	faceUndercutEdgesColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceVerticalFacesColor¶

MWMoldedPartValidationBuilder.FaceVerticalFacesColor¶

Returns or sets the color for applying to the vertical faces on the Face Tab page.

-------------------------------------

Getter Method

Signature FaceVerticalFacesColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature FaceVerticalFacesColor

Parameters:	faceVerticalFacesColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InApplyStatus¶

MWMoldedPartValidationBuilder.InApplyStatus¶

Returns or sets the flag that indicates the Apply status of the command, needed only in the interactive environment.

0: “Apply” has not been done before; 1: “Apply” has been done before.

-------------------------------------

Getter Method

Signature InApplyStatus

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InApplyStatus

Parameters:	inApplyStatus (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationCheckScope¶

MWMoldedPartValidationBuilder.InformationCheckScope¶

Returns or sets the check scope on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationCheckScope

Returns:
Return type:	`NXOpen.Tooling.MWMoldedPartValidationBuilderCheckScope`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationCheckScope

Parameters:	informationCheckScope (`NXOpen.Tooling.MWMoldedPartValidationBuilderCheckScope`) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR01¶

MWMoldedPartValidationBuilder.InformationColorR01¶

Returns or sets the color of row 1 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR01

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR01

Parameters:	informationColorR01 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR02¶

MWMoldedPartValidationBuilder.InformationColorR02¶

Returns or sets the color of row 2 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR02

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR02

Parameters:	informationColorR02 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR03¶

MWMoldedPartValidationBuilder.InformationColorR03¶

Returns or sets the color of row 3 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR03

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR03

Parameters:	informationColorR03 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR04¶

MWMoldedPartValidationBuilder.InformationColorR04¶

Returns or sets the color of row 4 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR04

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR04

Parameters:	informationColorR04 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR05¶

MWMoldedPartValidationBuilder.InformationColorR05¶

Returns or sets the color of row 5 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR05

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR05

Parameters:	informationColorR05 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR06¶

MWMoldedPartValidationBuilder.InformationColorR06¶

Returns or sets the color of row 6 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR06

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR06

Parameters:	informationColorR06 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR07¶

MWMoldedPartValidationBuilder.InformationColorR07¶

Returns or sets the color of row 7 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR07

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR07

Parameters:	informationColorR07 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR08¶

MWMoldedPartValidationBuilder.InformationColorR08¶

Returns or sets the color of row 8 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR08

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR08

Parameters:	informationColorR08 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR09¶

MWMoldedPartValidationBuilder.InformationColorR09¶

Returns or sets the color of row 9 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR09

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR09

Parameters:	informationColorR09 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR10¶

MWMoldedPartValidationBuilder.InformationColorR10¶

Returns or sets the color of row 10 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR10

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR10

Parameters:	informationColorR10 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR11¶

MWMoldedPartValidationBuilder.InformationColorR11¶

Returns or sets the color of row 11 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR11

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR11

Parameters:	informationColorR11 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationColorR12¶

MWMoldedPartValidationBuilder.InformationColorR12¶

Returns or sets the color of row 12 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationColorR12

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationColorR12

Parameters:	informationColorR12 (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationInspectFace¶

MWMoldedPartValidationBuilder.InformationInspectFace¶

Returns the face selected face for displaying the face properties.

-------------------------------------

Getter Method

Signature InformationInspectFace

Returns:
Return type:	`NXOpen.SelectFace`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimit¶

MWMoldedPartValidationBuilder.InformationLowerLimit¶

Returns or sets the lower limit of the range limit values on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimit

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimit

Parameters:	informationLowerLimit (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR01¶

MWMoldedPartValidationBuilder.InformationLowerLimitR01¶

Returns or sets the lower limit of row 1 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR01

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR01

Parameters:	informationLowerLimitR01 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR02¶

MWMoldedPartValidationBuilder.InformationLowerLimitR02¶

Returns or sets the lower limit of row 2 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR02

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR02

Parameters:	informationLowerLimitR02 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR03¶

MWMoldedPartValidationBuilder.InformationLowerLimitR03¶

Returns or sets the lower limit of row 3 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR03

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR03

Parameters:	informationLowerLimitR03 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR04¶

MWMoldedPartValidationBuilder.InformationLowerLimitR04¶

Returns or sets the lower limit of row 4 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR04

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR04

Parameters:	informationLowerLimitR04 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR05¶

MWMoldedPartValidationBuilder.InformationLowerLimitR05¶

Returns or sets the lower limit of row 5 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR05

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR05

Parameters:	informationLowerLimitR05 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR06¶

MWMoldedPartValidationBuilder.InformationLowerLimitR06¶

Returns or sets the lower limit of row 6 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR06

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR06

Parameters:	informationLowerLimitR06 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR07¶

MWMoldedPartValidationBuilder.InformationLowerLimitR07¶

Returns or sets the lower limit of row 7 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR07

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR07

Parameters:	informationLowerLimitR07 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR08¶

MWMoldedPartValidationBuilder.InformationLowerLimitR08¶

Returns or sets the lower limit of row 8 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR08

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR08

Parameters:	informationLowerLimitR08 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR09¶

MWMoldedPartValidationBuilder.InformationLowerLimitR09¶

Returns or sets the lower limit of row 9 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR09

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR09

Parameters:	informationLowerLimitR09 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR10¶

MWMoldedPartValidationBuilder.InformationLowerLimitR10¶

Returns or sets the lower limit of row 10 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR10

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR10

Parameters:	informationLowerLimitR10 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR11¶

MWMoldedPartValidationBuilder.InformationLowerLimitR11¶

Returns or sets the lower limit of row 11 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR11

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR11

Parameters:	informationLowerLimitR11 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationLowerLimitR12¶

MWMoldedPartValidationBuilder.InformationLowerLimitR12¶

Returns or sets the lower limit of row 12 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationLowerLimitR12

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationLowerLimitR12

Parameters:	informationLowerLimitR12 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationRangeType¶

MWMoldedPartValidationBuilder.InformationRangeType¶

Returns or sets the range type on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationRangeType

Returns:
Return type:	`NXOpen.Tooling.MWMoldedPartValidationBuilderRangeType`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationRangeType

Parameters:	informationRangeType (`NXOpen.Tooling.MWMoldedPartValidationBuilderRangeType`) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationSharpAngleLimit¶

MWMoldedPartValidationBuilder.InformationSharpAngleLimit¶

Returns or sets the sharp angle limit on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationSharpAngleLimit

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationSharpAngleLimit

Parameters:	informationSharpAngleLimit (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowBoundaryEdges¶

MWMoldedPartValidationBuilder.InformationShowBoundaryEdges¶

Returns or sets the option for turning on/off the highlight of the boundary edges of the sheet body on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowBoundaryEdges

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowBoundaryEdges

Parameters:	informationShowBoundaryEdges (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR01¶

MWMoldedPartValidationBuilder.InformationShowRangeR01¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 1 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR01

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR01

Parameters:	informationShowRangeR01 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR02¶

MWMoldedPartValidationBuilder.InformationShowRangeR02¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 2 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR02

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR02

Parameters:	informationShowRangeR02 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR03¶

MWMoldedPartValidationBuilder.InformationShowRangeR03¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 3 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR03

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR03

Parameters:	informationShowRangeR03 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR04¶

MWMoldedPartValidationBuilder.InformationShowRangeR04¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 4 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR04

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR04

Parameters:	informationShowRangeR04 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR05¶

MWMoldedPartValidationBuilder.InformationShowRangeR05¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 5 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR05

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR05

Parameters:	informationShowRangeR05 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR06¶

MWMoldedPartValidationBuilder.InformationShowRangeR06¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 6 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR06

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR06

Parameters:	informationShowRangeR06 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR07¶

MWMoldedPartValidationBuilder.InformationShowRangeR07¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 7 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR07

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR07

Parameters:	informationShowRangeR07 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR08¶

MWMoldedPartValidationBuilder.InformationShowRangeR08¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 8 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR08

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR08

Parameters:	informationShowRangeR08 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR09¶

MWMoldedPartValidationBuilder.InformationShowRangeR09¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 9 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR09

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR09

Parameters:	informationShowRangeR09 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR10¶

MWMoldedPartValidationBuilder.InformationShowRangeR10¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 10 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR10

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR10

Parameters:	informationShowRangeR10 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR11¶

MWMoldedPartValidationBuilder.InformationShowRangeR11¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 11 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR11

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR11

Parameters:	informationShowRangeR11 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowRangeR12¶

MWMoldedPartValidationBuilder.InformationShowRangeR12¶

Returns or sets the option of selecting the small radius faces within the range limit values of row 12 on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowRangeR12

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowRangeR12

Parameters:	informationShowRangeR12 (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationShowSharpEdges¶

MWMoldedPartValidationBuilder.InformationShowSharpEdges¶

Returns or sets the option for turning on/off the highlight of the sharp edges of the sheet body on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationShowSharpEdges

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationShowSharpEdges

Parameters:	informationShowSharpEdges (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimit¶

MWMoldedPartValidationBuilder.InformationUpperLimit¶

Returns or sets the upper limit on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimit

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimit

Parameters:	informationUpperLimit (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR01¶

MWMoldedPartValidationBuilder.InformationUpperLimitR01¶

Returns or sets the upper limit of row 1 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR01

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR01

Parameters:	informationUpperLimitR01 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR02¶

MWMoldedPartValidationBuilder.InformationUpperLimitR02¶

Returns or sets the upper limit of row 2 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR02

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR02

Parameters:	informationUpperLimitR02 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR03¶

MWMoldedPartValidationBuilder.InformationUpperLimitR03¶

Returns or sets the upper limit of row 3 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR03

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR03

Parameters:	informationUpperLimitR03 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR04¶

MWMoldedPartValidationBuilder.InformationUpperLimitR04¶

Returns or sets the upper limit of row 4 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR04

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR04

Parameters:	informationUpperLimitR04 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR05¶

MWMoldedPartValidationBuilder.InformationUpperLimitR05¶

Returns or sets the upper limit of row 5 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR05

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR05

Parameters:	informationUpperLimitR05 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR06¶

MWMoldedPartValidationBuilder.InformationUpperLimitR06¶

Returns or sets the upper limit of row 6 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR06

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR06

Parameters:	informationUpperLimitR06 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR07¶

MWMoldedPartValidationBuilder.InformationUpperLimitR07¶

Returns or sets the upper limit of row 7 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR07

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR07

Parameters:	informationUpperLimitR07 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR08¶

MWMoldedPartValidationBuilder.InformationUpperLimitR08¶

Returns or sets the upper limit of row 8 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR08

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR08

Parameters:	informationUpperLimitR08 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR09¶

MWMoldedPartValidationBuilder.InformationUpperLimitR09¶

Returns or sets the upper limit of row 9 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR09

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR09

Parameters:	informationUpperLimitR09 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR10¶

MWMoldedPartValidationBuilder.InformationUpperLimitR10¶

Returns or sets the upper limit of row 10 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR10

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR10

Parameters:	informationUpperLimitR10 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR11¶

MWMoldedPartValidationBuilder.InformationUpperLimitR11¶

Returns or sets the upper limit of row 11 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR11

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR11

Parameters:	informationUpperLimitR11 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUpperLimitR12¶

MWMoldedPartValidationBuilder.InformationUpperLimitR12¶

Returns or sets the upper limit of row 12 for the small radius faces on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUpperLimitR12

Returns:
Return type:	float

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUpperLimitR12

Parameters:	informationUpperLimitR12 (float) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InformationUseSingleTolerance¶

MWMoldedPartValidationBuilder.InformationUseSingleTolerance¶

Returns or sets the option for using a single tolerance for defining the range limit values on the Information Tab page.

-------------------------------------

Getter Method

Signature InformationUseSingleTolerance

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature InformationUseSingleTolerance

Parameters:	informationUseSingleTolerance (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionAssignToRegionOption¶

MWMoldedPartValidationBuilder.RegionAssignToRegionOption¶

Returns or sets the option for assigning the selected region faces to the cavity or core region on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionAssignToRegionOption

Returns:
Return type:	`NXOpen.Tooling.MWMoldedPartValidationBuilderAssignToRegion`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionAssignToRegionOption

Parameters:	regionAssignToRegionOption (`NXOpen.Tooling.MWMoldedPartValidationBuilderAssignToRegion`) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionCavityRegionColor¶

MWMoldedPartValidationBuilder.RegionCavityRegionColor¶

Returns or sets the color for applying to the cavity region faces on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionCavityRegionColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionCavityRegionColor

Parameters:	regionCavityRegionColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionCavityRegionTranslucency¶

MWMoldedPartValidationBuilder.RegionCavityRegionTranslucency¶

Returns or sets the translucency for applying to the cavity region faces on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionCavityRegionTranslucency

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionCavityRegionTranslucency

Parameters:	regionCavityRegionTranslucency (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionCoreRegionColor¶

MWMoldedPartValidationBuilder.RegionCoreRegionColor¶

Returns or sets the color for applying to the core region faces on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionCoreRegionColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionCoreRegionColor

Parameters:	regionCoreRegionColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionCoreRegionTranslucency¶

MWMoldedPartValidationBuilder.RegionCoreRegionTranslucency¶

Returns or sets the translucency for applying to the core region faces on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionCoreRegionTranslucency

Returns:
Return type:	int

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionCoreRegionTranslucency

Parameters:	regionCoreRegionTranslucency (int) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionFaces¶

MWMoldedPartValidationBuilder.RegionFaces¶

Returns the faces selected for assigning to the cavity or core region.

-------------------------------------

Getter Method

Signature RegionFaces

Returns:
Return type:	`NXOpen.SelectFaceList`

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionSelectCrossoverRegionFaces¶

MWMoldedPartValidationBuilder.RegionSelectCrossoverRegionFaces¶

Returns or sets the option for including or removing the crossover region faces in the selection on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionSelectCrossoverRegionFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionSelectCrossoverRegionFaces

Parameters:	regionSelectCrossoverRegionFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionSelectCrossoverVerticalFaces¶

MWMoldedPartValidationBuilder.RegionSelectCrossoverVerticalFaces¶

Returns or sets the option for including or removing the crossover vertical faces in the selection on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionSelectCrossoverVerticalFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionSelectCrossoverVerticalFaces

Parameters:	regionSelectCrossoverVerticalFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionSelectUnknownFaces¶

MWMoldedPartValidationBuilder.RegionSelectUnknownFaces¶

Returns or sets the option for including or removing the unknown faces in the selection on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionSelectUnknownFaces

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionSelectUnknownFaces

Parameters:	regionSelectUnknownFaces (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionShowIncompleteLoops¶

MWMoldedPartValidationBuilder.RegionShowIncompleteLoops¶

Returns or sets the option for turning on/off the highlight of the incomplete loop edges.

-------------------------------------

Getter Method

Signature RegionShowIncompleteLoops

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionShowIncompleteLoops

Parameters:	regionShowIncompleteLoops (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionShowInternalLoops¶

MWMoldedPartValidationBuilder.RegionShowInternalLoops¶

Returns or sets the option for turning on/off the highlight of the internal loop edges.

-------------------------------------

Getter Method

Signature RegionShowInternalLoops

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionShowInternalLoops

Parameters:	regionShowInternalLoops (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionShowPartingEdges¶

MWMoldedPartValidationBuilder.RegionShowPartingEdges¶

Returns or sets the option for turning on/off the highlight of the parting edges.

-------------------------------------

Getter Method

Signature RegionShowPartingEdges

Returns:
Return type:	bool

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionShowPartingEdges

Parameters:	regionShowPartingEdges (bool) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionUndefinedRegionColor¶

MWMoldedPartValidationBuilder.RegionUndefinedRegionColor¶

Returns or sets the color for applying to the undefined region faces on the Region Tab page.

-------------------------------------

Getter Method

Signature RegionUndefinedRegionColor

Returns:
Return type:	Id

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

-------------------------------------

Setter Method

Signature RegionUndefinedRegionColor

Parameters:	regionUndefinedRegionColor (Id) –

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

Method Detail¶

Calculate¶

MWMoldedPartValidationBuilder.Calculate¶

Calculate button on the Calculate Tab page.

Signature Calculate()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

FaceSetAllFacesColor¶

MWMoldedPartValidationBuilder.FaceSetAllFacesColor¶

Action button for setting color on all faces on the Face Tab page.

Signature FaceSetAllFacesColor()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

InitMpvData¶

MWMoldedPartValidationBuilder.InitMpvData¶

Initialize the MPV data for performing analysis in Molded Part Validation.

Signature InitMpvData(changeBody)

Parameters:	changeBody (int) – 0: No change in the selected body; 1: Change in the selected body; 2: Change in direction for the selected body.

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

PerformModelPropertiesCalculation¶

MWMoldedPartValidationBuilder.PerformModelPropertiesCalculation¶

Perform model properties calculation if the calculation has not been performed before.

Signature PerformModelPropertiesCalculation()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

PerformSharpCornersCalculation¶

MWMoldedPartValidationBuilder.PerformSharpCornersCalculation¶

Perform the sharp corners calculation if the calculation has not been performed before.

Signature PerformSharpCornersCalculation()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

ProcessFaceSplit¶

MWMoldedPartValidationBuilder.ProcessFaceSplit¶

Action button for invoking the Split Face command on the Face Tab page.

Signature ProcessFaceSplit()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

RegionSetRegionsColor¶

MWMoldedPartValidationBuilder.RegionSetRegionsColor¶

Action button for setting color on the cavity, core and undefined region faces on the Region Tab page.

Signature RegionSetRegionsColor()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

SetCalculationProductBody¶

MWMoldedPartValidationBuilder.SetCalculationProductBody¶

Set the product body to be analyzed on the Calculate Tab page.

Signature SetCalculationProductBody(calculationProductBody)

Parameters:	calculationProductBody (`NXOpen.Body`) – The product body

New in version NX10.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

UpdateEjectDirection¶

MWMoldedPartValidationBuilder.UpdateEjectDirection¶

Update the eject direction.

Signature UpdateEjectDirection()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

UpdateMpvData¶

MWMoldedPartValidationBuilder.UpdateMpvData¶

Update the MPV data used in performing analysis in Molded Part Validation whenever there are changes in data on dialog.

Signature UpdateMpvData()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

UpdateSharpEdgesInformation¶

MWMoldedPartValidationBuilder.UpdateSharpEdgesInformation¶

Update the sharp edges information based on the new sharp angle limit which has been changed by the user.

Signature UpdateSharpEdgesInformation()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

UpdateSmallRadiusFacesInformation¶

MWMoldedPartValidationBuilder.UpdateSmallRadiusFacesInformation¶

Update the small radius faces information based on the new range limits of the radius which has been changed by the user.

Signature UpdateSmallRadiusFacesInformation()

New in version NX8.0.0.

License requirements: ug_mold_design (“UG MOLD”) OR ug_prod_des_advisor (“Product Design Advisor”) OR prog_die_wizard (“UG/Progressive Die Wizard”) OR die_engineering (“DIE ENGINEERING”) OR ug_die_design (“Die Design”) OR nx_electrode_wizard (“NX Electrode Wizard”)

Validate¶

MWMoldedPartValidationBuilder.Validate¶

Validate whether the inputs to the component are sufficient for commit to be called.

If the component is not in a state to commit then an exception is thrown. For example, if the component requires you to set some property, this method will throw an exception if you haven’t set it. This method throws a not-yet-implemented NXException for some components.

Signature Validate()

Returns:	Was self validation successful
Return type:	bool

New in version NX3.0.1.

License requirements: None.